Physics Class 12 Part I…
🏠 હોમ લૉગિન
ટોપિક 12 / 38

Kirchhoffs Laws Bridges

🎓 Class 12 Physics CBSE Theory Ch 3 – Current Electricity ⏱ ~14 min
🌐 ભાષા:

આ MCQ મોડ્યુલ આના પર આધારિત છે: Kirchhoffs Laws Bridges

આ મૂલ્યાંકન આના પર આધારિત હશે: Kirchhoffs Laws Bridges

મૂલ્યાંકન બનાવવામાં તેમની સામગ્રી સામેલ કરવા ચિત્રો, PDF અથવા Word દસ્તાવેજ અપલોડ કરો.

Kirchhoffs Laws Bridges

3.14 Kirchhoff's Rules

Many electric circuits cannot be reduced to simple series-parallel combinations — they contain multiple loops or several EMF sources. Two rules formulated by G.R. Kirchhoff in 1847 allow us to analyse any such network systematically.

3.14.1 Junction Rule (KCL)

Kirchhoff's Junction Rule: The algebraic sum of currents meeting at any junction is zero — \(\sum I = 0\). This expresses conservation of charge: charge cannot accumulate at a point in a steady current.

3.14.2 Loop Rule (KVL)

Kirchhoff's Loop Rule: The algebraic sum of changes in potential around any closed loop is zero — \(\sum V = 0\). This expresses conservation of energy: a unit charge moved around a loop returns to the same potential.

Sign convention for the loop rule:

  • Choose a direction (clockwise or counter-clockwise) to traverse the loop.
  • For a resistor: drop in potential (−IR) if you traverse in the direction of current; rise (+IR) if against.
  • For an EMF source: rise (+ε) if you go from − to +; drop (−ε) if from + to −.
(a) Junction rule: I₁+I₂ = I₃ I₁ I₂ I₃ (b) Loop rule: ε − IR₁ − IR₂ = 0 ε R₁ R₂ ↻ I
Fig. 3.11: (a) Junction rule (KCL) — sum of currents in equals sum of currents out. (b) Loop rule (KVL) — sum of EMFs equals sum of IR drops around any closed loop.

3.15 Wheatstone Bridge

An important application of Kirchhoff's rules is the Wheatstone bridge — a clever circuit for measuring an unknown resistance accurately. Four resistors P, Q, R and S are connected to form a quadrilateral ABCD. A galvanometer G is connected between the diagonally opposite points B and D, and a battery between A and C.

A B C D P Q R S G ε
Fig. 3.12: Wheatstone bridge: four resistors P, Q, R, S in a diamond, galvanometer G between B and D, battery between A and C.

When the bridge is balanced — i.e., the galvanometer shows zero deflection (no current through G) — applying the loop and junction rules gives the famous balance condition:

\[ \dfrac{P}{Q} = \dfrac{R}{S} \quad\Longleftrightarrow\quad PS = QR \]

If three resistances are known, the fourth can be found.

3.16 Meter Bridge (Slide-Wire Bridge)

A practical Wheatstone bridge built around a uniform 1 m resistance wire stretched between two ends A and C of a meter scale. A jockey J slides along the wire, dividing it into lengths ℓ (from A to J) and (100 − ℓ) cm (from J to C). The unknown resistance X and a known resistance R fill the other two arms.

R X G jockey J A (0 cm) ℓ cm C (100 cm) ε
Fig. 3.13: A meter bridge — uniform 1 m wire between A and C; jockey J slides until galvanometer shows zero. Then R/X = ℓ/(100−ℓ).

At balance,

\[ \dfrac{R}{X} = \dfrac{\rho \ell / A}{\rho (100-\ell)/A}=\dfrac{\ell}{100-\ell}\quad\Rightarrow\quad X = R\,\dfrac{100-\ell}{\ell} \]

3.17 Potentiometer

A potentiometer uses a long uniform wire AB of resistance per unit length k. A steady current I flows through it from an auxiliary driver cell, so the potential drop per unit length φ = Ik is constant. By tapping a sliding contact (jockey) along the wire we can pick off any voltage between 0 and the full drop.

ε₀ A B J G ε
Fig. 3.14: Potentiometer used to measure unknown EMF ε. Jockey J slides along AB until galvanometer shows zero. Then ε = φ × ℓ_J.

3.17.1 Comparing EMFs of Two Cells

Connect cells of EMFs ε₁ and ε₂ alternately in the secondary circuit. Find balancing lengths ℓ₁ and ℓ₂. Since at balance ε = φ·ℓ:

\[ \dfrac{\varepsilon_1}{\varepsilon_2} = \dfrac{\ell_1}{\ell_2} \]

3.17.2 Measuring Internal Resistance

Find balance length ℓ₁ with the cell of EMF ε open-circuited. Then close a known resistor R across the cell and find new balance ℓ₂. With current flowing, terminal voltage V = ε − Ir = εR/(R+r). Hence,

\[ \dfrac{\varepsilon}{V} = \dfrac{\ell_1}{\ell_2}\quad\Rightarrow\quad r = R\left(\dfrac{\ell_1}{\ell_2} - 1\right) \]
Why a potentiometer is "ideal": At balance no current flows through the cell under test, so its terminal voltage equals its EMF. A voltmeter, by contrast, always draws a small current and so reads slightly less than ε.

Interactive Simulation: Wheatstone Bridge Balance Solver L4 Analyse

Set three resistors and find the value of the fourth needed to balance the bridge (no current through the galvanometer). Try unbalanced cases and watch the predicted galvanometer current.

Balance condition P/Q = R/S → 0.500 vs 0.500
Status: BALANCED — no galvanometer current
S to balance the bridge for given P, Q, R: S = QR/P = 30.00 Ω

Worked Example 1: Two-Loop Network with Kirchhoff

In the network shown, two batteries of EMFs 10 V and 4 V are connected as in the figure, with internal resistances 1 Ω each, joined to two external resistors of 5 Ω. Find the currents in each branch.

Let I₁ flow from the 10-V cell, I₂ from the 4-V cell, and I = I₁ + I₂ through the common branch. Applying KVL to the two loops gives:
Loop 1: 10 = I₁(1) + 5(I₁+I₂) ⇒ 6I₁ + 5I₂ = 10
Loop 2: 4 = I₂(1) + 5(I₁+I₂) ⇒ 5I₁ + 6I₂ = 4
Solving: I₁ ≈ 1.45 A, I₂ ≈ −0.55 A (i.e., direction opposite to assumed). Net I ≈ 0.91 A through the parallel branch.

Worked Example 2: Wheatstone Bridge

In a Wheatstone bridge the resistors P = 100 Ω, Q = 10 Ω and R = 4 Ω. Find S that balances the bridge.

\[ \dfrac{P}{Q}=\dfrac{R}{S} \Rightarrow S = \dfrac{QR}{P} = \dfrac{10 \times 4}{100} = \boxed{0.4\ \Omega} \]

Worked Example 3: Potentiometer Comparison

In a potentiometer experiment, a Daniell cell gives a balance length of 125 cm. When this cell is replaced by a Leclanché cell, the balance length becomes 145 cm. If EMF of the Daniell cell is 1.08 V, find the EMF of the Leclanché cell.

\[ \dfrac{\varepsilon_1}{\varepsilon_2}=\dfrac{\ell_1}{\ell_2} \Rightarrow \varepsilon_2 = 1.08 \times \dfrac{145}{125} \approx \boxed{1.25\ \text{V}}\]
Activity 3.4 — Locating the Null Point on a Meter BridgeL3 Apply

Materials: meter bridge, jockey, galvanometer, key, battery, known resistance R = 5 Ω, unknown resistor X.

Procedure:

  1. Connect R in the left gap and X in the right gap.
  2. Close the key. Slide the jockey J along the wire until the galvanometer shows zero deflection. Note the length ℓ.
  3. Calculate X = R(100−ℓ)/ℓ.
  4. Repeat by interchanging R and X to eliminate end errors and average the readings.
Predict: If R is greater than X, will the null point lie closer to A or to C?

Observation: If R > X, ℓ > 50 cm (null shifts toward C); if R < X, ℓ < 50 cm. The null point gives X via the simple ratio formula.

Conclusion: The meter bridge applies the Wheatstone principle with the wire serving as two of the four arms. It is sensitive only when ℓ ≈ 50 cm — so choose R close to the expected X.

Competency-Based Questions

A student sets up a Wheatstone bridge to measure an unknown low resistance and a potentiometer to compare two cells. She finds that her galvanometer is sluggish, and her meter-bridge null point is at 73.2 cm with R = 4 Ω in the left gap.

Q1. The unknown resistance X in the right gap is: L3 Apply

  • (a) 1.46 Ω
  • (b) 4.00 Ω
  • (c) 10.93 Ω
  • (d) 0.92 Ω
(a) X = R(100−ℓ)/ℓ = 4 × (26.8/73.2) ≈ 1.46 Ω.

Q2. Short Answer: Why is the potentiometer considered an "ideal voltmeter" while comparing EMFs of cells? L4 Analyse

At the balance point of a potentiometer, no current is drawn from the cell whose EMF is being measured; therefore there is no Ir drop, and the terminal voltage equals the true EMF. Voltmeters, on the other hand, always draw a small current and so read V = ε − Ir slightly less than ε.

Q3. Kirchhoff's junction rule expresses conservation of: L1 Remember

  • (a) energy
  • (b) momentum
  • (c) charge
  • (d) flux
(c). KCL: ΣI = 0 means charge cannot accumulate at a node — conservation of charge.

Q4. True/False: A Wheatstone bridge is most sensitive when all four resistances are of the same order. Justify. L5 Evaluate

TRUE. The galvanometer's response to a small change in any resistor is largest when the four arms are comparable; if one is much larger than the others, the bridge is very insensitive and the null is hard to locate precisely.

Q5. HOT: In a potentiometer experiment with a 1.5 V driver cell driving 1.0 A through a 10 Ω wire, what is the potential gradient (in V/cm) along the 100 cm wire? Also, what balancing length will correspond to a 0.45 V cell? L6 Create

Total drop across wire = IR = 1.0 × 10 = 10 V. Potential gradient φ = 10 V / 100 cm = 0.10 V/cm.
Wait — 1.5 V cannot drive 10 V across 10 Ω. Re-check: actually with only 1.5 V driver and 10 Ω wire alone, current is 1.5/10 = 0.15 A and drop = 1.5 V (gradient 0.015 V/cm). For ε = 0.45 V: ℓ = 0.45/0.015 = 30 cm.

Assertion–Reason Questions

Choose: (A) Both A and R true; R explains A. (B) Both true; R does not explain A. (C) A true, R false. (D) A false, R true.

Assertion (A): Kirchhoff's loop rule is a consequence of conservation of energy.

Reason (R): The work done in moving a unit charge once around a closed loop is zero in an electrostatic field.

(A) Both true and R explains A. ΣV = 0 around any loop ↔ conservative field.

Assertion (A): A potentiometer can measure EMF more accurately than a voltmeter.

Reason (R): A voltmeter has very high resistance.

(B). Both true but R is not the correct explanation. The reason a potentiometer is more accurate is that at balance it draws ZERO current from the cell under test, so no Ir drop occurs.

Assertion (A): The sensitivity of a meter bridge is greatest when the null point lies near the middle of the wire.

Reason (R): The four arms of the bridge are then comparable in resistance.

(A) Both true and R explains A. With ℓ ≈ 50 cm the bridge arms are roughly equal, giving best sensitivity.

Frequently Asked Questions - Kirchhoffs Laws Bridges

What is the main concept covered in Kirchhoffs Laws Bridges?
In NCERT Class 12 Physics Chapter 3 (Current Electricity), "Kirchhoffs Laws Bridges" covers the core principles and equations students need for board exam success. The MyAiSchool lesson explains the topic with definitions, derivations, worked examples, and interactive simulations. Key formulas and dimensional analysis are included to build conceptual depth and problem-solving skills aligned with the CBSE 2025-26 syllabus.
How is Kirchhoffs Laws Bridges useful in real-life applications?
Real-life applications of "Kirchhoffs Laws Bridges" from NCERT Class 12 Physics Chapter 3 include electronics, communication systems, medical imaging, solar energy, semiconductor devices, and modern technology. The MyAiSchool lesson links every concept to a tangible example so students see physics as a problem-solving framework for the physical world, not as abstract formulas.
What are the key formulas in Kirchhoffs Laws Bridges?
Key formulas in "Kirchhoffs Laws Bridges" (NCERT Class 12 Physics Chapter 3 Current Electricity) are derived step-by-step in the MyAiSchool lesson. Students should memorize the final formula AND understand its derivation for full board marks. Each formula is listed with its dimensional formula, SI unit, applicability range, and common pitfalls. The Summary section at the end of each part includes a quick-reference formula card.
How does this part connect to other parts of Chapter 3?
NCERT Class 12 Physics Chapter 3 (Current Electricity) is structured so each part builds on the previous one. "Kirchhoffs Laws Bridges" connects directly to neighbouring parts via shared definitions, units, and methodology. The MyAiSchool lesson cross-references related concepts with internal links so students can navigate the whole chapter as one connected story rather than disconnected fragments.
What types of CBSE board questions come from Kirchhoffs Laws Bridges?
CBSE board questions from "Kirchhoffs Laws Bridges" typically include: (1) 1-mark MCQs on definitions and formulas, (2) 2-mark short-answer derivations or applications, (3) 3-mark numerical problems with units, (4) 5-mark long-answer derivations followed by application. The MyAiSchool lesson tags each Competency-Based Question (CBQ) with Bloom level (L1-L6) so students know how to study for each weight.
How can students use the interactive simulation effectively?
The interactive simulation in the "Kirchhoffs Laws Bridges" lesson allows students to adjust input parameters (sliders or selectors) and see physical quantities update in real time. To use it effectively: (1) try extreme values to understand limiting cases, (2) compare with the analytical formula, (3) check unit consistency, (4) test special configurations from worked examples. The simulation reinforces conceptual intuition that pure formula manipulation cannot.
AI ટ્યુટર
Physics Class 12 Part I – NCERT (2025-26)
તૈયાર
નમસ્તે! 👋 હું ગૌરા છું, Kirchhoffs Laws Bridges માટે તમારું AI ટ્યુટર. આરામથી પાઠ ભણો — જ્યારે પણ કોઈ શંકા થાય, બસ મને પૂછો! હું મદદ માટે અહીં જ છું.

📝 આ ટોપિકની પ્રેક્ટિસ કરો — મોક પરીક્ષાઓ

🎯 Physics ની પ્રેક્ટિસ કરો

તમે જે ભણ્યા તેનું પૂરું પેપર આપો, પ્રશ્ન દીઠ તપાસાયેલું.

બોર્ડ પરીક્ષા સેમ્પલ પેપર

આ વિષયનાં બધાં પેપર →

મોક પરીક્ષાઓ

આ વિષયની બધી મોક પરીક્ષાઓ →

🎁 Join our community and get free AI credits!
WhatsApp